跳至产品信息
1 / 6

Noseto

Noseto SK5 210mm Gyuto S-Grind SK5 carbon with Crape Myrtle Burl, Cow Horn Ferrule

Noseto SK5 210mm Gyuto S-Grind SK5 carbon with Crape Myrtle Burl, Cow Horn Ferrule

常规价格 $558.00 AUD
常规价格 促销价 $558.00 AUD
促销 售罄
已含税费。
Add Custom Engraving
数量

Noseto SK5 Gyuto 210mm

Three metals, one maker, and a hollow ground into each side of the blade by hand. Our signature gyuto: a 52100 core clad in SK5 carbon, nickel and red copper, at 165g for a 210mm blade. The thinnest and most carefully made knife we sell.

The grind

This is the reason the knife exists. Look at it end-on and the cross-section traces an S: convex just above the edge, then hollowed out through the middle of the blade face. That hollow is an air gap. Food parts at the edge, meets nothing behind it, and falls away instead of climbing the blade and sticking, which is the most tiring thing about prepping a kilo of potatoes with a flat-sided knife.

An S-grind cannot be made on a jig. It is cut by hand on a wheel by someone reading the steel as they go, and it is the clearest evidence of a maker’s skill visible on a finished blade. Very few knives at any price do it properly, which is why those that do are made one at a time.

The steel

The core is 52100, a high-carbon bearing steel with a famously fine grain. Fine grain is what lets an edge go truly keen rather than merely sharp, and it is why custom makers keep returning to 52100 when they could reach for something more fashionable.

The cladding is where the knife gets its face: layers of SK5 carbon steel, nickel and red copper. The nickel stays bright and refuses to etch, the copper reads warm and pink, and the carbon goes dark, so the pattern shows in three tones instead of the usual two. Copper is rare in a kitchen blade because it is difficult to weld to steel, and most makers do not attempt it.

The blade

210mm and 165g. A standard 210mm gyuto runs closer to 180g, and the difference is the steel hollowed out of the blade face. The result falls through an onion under its own weight and stays nimble at the end of a long session rather than needing to be driven.

The handle

Crape myrtle burl with a cow horn ferrule. Burl is the figured wood from a growth in the trunk, so the grain swirls rather than runs, and no two blanks are alike. It is dense enough to take a polish closer to stone than timber, and the horn darkens alongside the blade. Every handle is different, and the one in the photographs is the one you receive.

Specifications

Type Gyuto, chef knife
Blade length 210mm
Grind Hand-ground S-grind
Core steel 52100 high-carbon
Cladding SK5 carbon steel, nickel, red copper
Handle Crape myrtle burl, cow horn ferrule
Weight 165g
Construction Made by hand, one at a time

Care

Core and cladding are both carbon steel, so the whole blade is reactive and will darken with use. The grey patina that forms is normal, protects the steel, and on this knife is part of the design.

Wipe the blade down as you work, especially after onion, tomato or citrus, and dry it fully before it goes away. Never leave it wet. Hand wash only, never the dishwasher. Keep it off bone and frozen product, and never twist or pry. Maintain the edge on a whetstone. A spot of red rust lifts off with a rust eraser and is not damage.

If you want a knife you can leave on the sink, take one of our stainless gyutos instead. This one rewards attention.

Sharpening

We sharpen by hand in the basement at 137 Broadway, and a hand-ground S-grind should never meet a machine. Bring it to us and we will keep the geometry the maker gave it.

查看完整详细信息